|
|
|
|
 |
|
| |
|
|
| |
Cables and Cable Assemblies |
|
| |
|
|
| |
| Optical Fiber Cables |
| |
We offer a complete range of terrestrial fiber optic cables for a variety of applications
in telecommunications networks. The Product range includes the following both
SINGLE MODE as well as MULTIMODE cable which are used depending on the
application. In addition to the above, we also offer a wide range of cables depending
of the installation. The range includes the following: |
| |
|
| 1 |
Duct cables for both indoor and outdoor applications |
| 2 |
Direct buried cables |
| 3 |
Aerial Cables including figure 8 cables |
| 4 |
Fully automated, highly intelligent interface |
| 5 |
Tight buffered cables |
|
| |
In addition to the above, we could also assist you in arriving at the optimum design
for your cabling needs depending on your requirements and conditions due to our
technical expertise on the subject. |
|
|
 |
|
|
| |
|
|
| |
 |
|
| Patch Chords |
| |
Fiber optic patch cord is one of most commonly used components in fiber optic network.
They are used for linking the equipment and components in the fiber optic network. They
are of various types depending on the connectors used. Some of the types of connectors
are SC, ST, FC, LC, E200 & MTRJ. Typical fiber optic patch cord cable diameter can be 0.9mm,
2mm, or 3mm. Depending on the network and application, we supply single mode and
multimode patch cords Features of fiber optic patch cord: |
| |
|
| 1 |
Low insertion loss and High Return Loss |
| 2 |
Temperature stability - Operating temperature: -20 to +75°C |
| 3 |
High durability |
| 4 |
All patch cords are 100% tested |
|
|
|
|
| |
|
|
| |
| Pigtails |
| |
Fiber pigtail is a piece of fiber optic cable with only one fiber optic connector on one
side of the cable typically used to link the fiber optic cable with fiber optic equipment
while the other side of the pigtail is spliced to the fiber usually inside an ODF unit.
Depending on the application they can be single mode and multimode fiber optic
pigtails. Pigtails are further classified depending on the connectors used. Some of the
different types are SC, FC, ST, LC, MTRJ, E200, etc. |
|
|
 |
|
|
| |
|
|
| |
 |
|
| Adaptors and connectors |
| |
Fiber optic adapters are also called mating sleeves. They are used to connect optical
connectors of same type, such as FC, SC and ST. Optical adapters are widely used in
light distribution frame (ODF), the optical fiber communications equipment, the test
equipments and so on. Our range of connectors provide reliable solutions for fiber
connections and are fully comparable with the products from other suppliers in the
market. We also supply Hybrid Adaptors. |
|
|
|
| |
|
|
| |
| Optical Distribution Frame and Fiber Optic Patch Panels |
| |
Optical distribution frame is a fiber optic management unit used to organize the fiber
optic cable connections. frame It is usually used indoors and comes in a wide range
of sizes depending on the numbers of connections needed. The optical distribution
frames are of modular design with siding type trays inside and these ODF could
be pre-installed with various kinds of fiber optic adapters and pigtails. The optical
distribution frame is with standard 19 inch size and it is properly designed to control
the bend radius of the cable inside the enclosure to avoid extra optical loss. These
optical distribution frames are ideal for indoor fiber optic cable connections storage,
distribution and management. We supply a wide range of ODFs from 12f onwards. |
|
|
 |
|
|
| |
|
|
|
|
 |
|
|
|
|
